Page 1 of 5 123 ... LastLast
Results 1 to 18 of 89

Thread: Milka Build thread

  1. #1
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97

    Milka Build thread

    As a few people have asked for this, I am going to do a mini build thread on here. Please if you have any questions or want to see and modifications let me know and I will post pics, measurements, logs, etc. My full build thread is here http://www.ozaudi.com/forums/a6-s6-r...-thread-6.html

    So the car started as a 2003 built MY2004 Aus delivered RS6, came with 19' 5 spokes, recaro interior, matt black interior handles etc, carbon trim, etc.

    My current mod list is something close to this: (I will modify as I remember more)
    Hotchkis sways
    KW v3 Coilovers
    Adjustable front upper control arms
    B7 RS4 wheels 265/35/19 Toyo Proxes T1S
    Alcon front brakes, RS6 Plus rear rotors
    Stainless lines brake lines all round
    Twin GTX3071 Turbos, Twin scroll .82 housings
    Tial MV-S external wastegates set to 13 psi base pressure
    Custom exhaust manifold, Twin scroll with single Tial per bank
    Milltek Exhaust with cats and resonators
    Custom 3' dump joined into Milltek cats
    Twin LC-1 wideband 02s
    Twin BMC OTA Carbon airfilters
    Twin A8 MAFs
    Custom intake piping joining the stock air intakes into BMC OTAs then A8 MAFs then into enlarged Y at back of engine
    Re-core'd RS6 intercoolers with Garrett 4.25' thick cores
    Removed additional radiators
    Weldon fuel pressure regulator
    Integrated engineering billet 1.8T rails modified to fit RS6
    -8 teflon fuel lines with speedflow fittings
    Bosch EV14 980cc injectors
    Phenolic Spacers 1.8T port matched to RS6 heads/manifolds
    0A3 B7 RS4 gearbox
    Custom 6mm gearbox spacer
    Modified TDI 6th gear
    B7 RS4 clutch slave
    A6 manual Clutch master
    A6 manual clutch pedal/brake pedal
    ClutchMasters FX850 Twin Plate clutch
    custom front half shafts (using existing stock RS6 CVs)
    custom gearbox mount brackets
    modified tail shaft
    modified oil cooler to be just engine oil no gearbox
    shifter from B5 S4
    W8 ABS controller
    Catch Can with baffles (removed SAI and replaced with catch can)
    Wavetrac LSD
    Self Tuned via TunerPro with the assistance of PRJ ;-)

    Currently working on:
    Twin Walbro 416 E85 intank pumps (with option of going to Radium external surge tank if needed but trying to avoid this)
    E85 Conversion
    Tilton Carbon/Carbon Triple Plate Clutch
    B7 RS4 shifter
    R8 Rims /w 255/35/19 fronts and 295/30/19 rears

    Spare engine being worked on (aiming to run >30psi)
    Heads fully built and ready to rev over 8500 (I will set red line to 8000)
    Pauter rods
    Need to figure out Pistons/rings for spare blocks
    (If anyone knows a company that has done Alusil pistons/rings before please let me know, second option will be to sleave the block)
    Last edited by milka; February 27th, 2014 at 02:29.

  2. #2
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Car prior to pulling apart for the manual conversion and big turbos, external gates, etc

    Click image for larger version. 

Name:	Pre rebuilding001.jpg 
Views:	3372 
Size:	85.0 KB 
ID:	14977

    Click image for larger version. 

Name:	Pre rebuilding002.jpg 
Views:	3256 
Size:	50.2 KB 
ID:	14978

    Engine mated to B7 RS4 gearbox

    Click image for larger version. 

Name:	32Gb20110503(20844).jpg 
Views:	3969 
Size:	95.2 KB 
ID:	14979

    Comparing the GTX3071s to stock RS6 turbos

    Click image for larger version. 

Name:	Compare Turbos.jpg 
Views:	3437 
Size:	66.7 KB 
ID:	14980

    Click image for larger version. 

Name:	Compare Turbos1.jpg 
Views:	3134 
Size:	68.7 KB 
ID:	14981
    Last edited by milka; February 27th, 2014 at 02:44.

  3. #3
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Manifolds being fabricated

    Click image for larger version. 

Name:	Manifolds 001.jpg 
Views:	3139 
Size:	85.9 KB 
ID:	14982

    Click image for larger version. 

Name:	Manifolds 002.jpg 
Views:	3127 
Size:	72.0 KB 
ID:	14983


    Test fitting on engine
    Click image for larger version. 

Name:	Manifolds 003.jpg 
Views:	3329 
Size:	86.9 KB 
ID:	14984

    Click image for larger version. 

Name:	Manifolds 004.jpg 
Views:	3194 
Size:	73.7 KB 
ID:	14985

    Click image for larger version. 

Name:	Manifolds 005.jpg 
Views:	3335 
Size:	88.7 KB 
ID:	14986


    Test fitting clearances in the engine bay
    Click image for larger version. 

Name:	Testfitting001.jpg 
Views:	3086 
Size:	80.9 KB 
ID:	14987

    Click image for larger version. 

Name:	Testfitting002.jpg 
Views:	3175 
Size:	65.8 KB 
ID:	14988
    Last edited by milka; February 27th, 2014 at 04:05.

  4. #4
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Checking Flywheel vs flex plate alignment of the tone ring
    Click image for larger version. 

Name:	B7_RS4_Flywheel001.jpg 
Views:	3117 
Size:	59.2 KB 
ID:	14989

    Click image for larger version. 

Name:	Flexplate001.jpg 
Views:	3192 
Size:	39.1 KB 
ID:	14990

    Click image for larger version. 

Name:	Flexplate002.jpg 
Views:	3156 
Size:	98.8 KB 
ID:	14991

    Now test fitting exhaust manifolds with turbos attached and wastegates attached.

    Click image for larger version. 

Name:	Wastegates_mounted001.jpg 
Views:	3439 
Size:	106.2 KB 
ID:	14992
    Last edited by milka; February 27th, 2014 at 04:11.

  5. #5
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Fabricating the dump pipes and wastegate piping
    Click image for larger version. 

Name:	DumpPipes001.jpg 
Views:	3232 
Size:	77.0 KB 
ID:	14993


    Click image for larger version. 

Name:	DumpPipes002.jpg 
Views:	3656 
Size:	74.0 KB 
ID:	14994

    Full length showing shifter fitted and dump pipes fabricated into existing Milltek downpipes/cats
    Click image for larger version. 

Name:	DumpPipes003.jpg 
Views:	3071 
Size:	56.9 KB 
ID:	14995


    Passenger turbo from the side (yes yes I'm in Australia ;-) )
    Click image for larger version. 

Name:	DumpPipes004.jpg 
Views:	3131 
Size:	75.2 KB 
ID:	14996
    Click image for larger version. 

Name:	DumpPipes005.jpg 
Views:	3191 
Size:	95.6 KB 
ID:	14997

    A little bit of customization needed to make the wastegate dump fit past the shift rods. Everything was very tight!
    Click image for larger version. 

Name:	shifterRodMod001.jpg 
Views:	2985 
Size:	68.5 KB 
ID:	14998
    Last edited by milka; February 27th, 2014 at 04:16.

  6. #6
    Registered User 4everRS's Avatar
    Join Date
    Nov 2009
    Location
    MN
    Posts
    2,405
    Sounds like quite a job.

    In this forum I think you only have a couple hours to edit a post. After that you can't edit or add pics.

    Edit: I see pics are coming.
    Avus Silver RS6 - Viper Stage 2 ECU/TCU - Water/Meth Injection - Frozen Rotors - Hbars - clear corners - Hella smoked tails - gutted precats

  7. #7
    Registered User
    Join Date
    Feb 2013
    Location
    Annapolis, MD
    Posts
    53
    Subscribed

  8. #8
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Quote Originally Posted by 4everRS View Post
    Sounds like quite a job.

    In this forum I think you only have a couple hours to edit a post. After that you can't edit or add pics.

    Edit: I see pics are coming.
    Thanks for letting me know, I just filled the posts with some pics that will show how big everything is, and how little room there is to put the larger turbos in..... It does fit just!

  9. #9
    Registered User
    Join Date
    Dec 2010
    Location
    Charleston, SC
    Posts
    600
    Looks like a great build. how was the B7 trans mate complication? Straight forward with a custom plate?
    03 RS6 :: 01 allroad

  10. #10
    Registered User lswing's Avatar
    Join Date
    May 2011
    Location
    Eugene, OR, again...
    Posts
    4,760
    Wonderful fabrication work and photos, thanks for sharing!
    Ace/Edge TC - Tozo Trans - MTM TCU - REVO/ME7 tune - Wagner IC's w/ Venair Hoses - Aux Radiator delete - Hotchkis Sways - Hawk HPS Pads - Koni Sport Struts - Scroll KO4 Turbos - Devil's Own WM - 421whp/452wtq on Mustang Dyno - http://www.audirssix.com

  11. #11
    Registered User
    Join Date
    Mar 2007
    Location
    Evil Empire
    Posts
    466
    Thank you.

  12. #12
    Registered User MaxRS6's Avatar
    Join Date
    Mar 2009
    Location
    Here
    Posts
    2,673
    Wowza- +1- Thanks for sharing your work product!
    210K miles rolled

  13. #13
    Registered User ben916's Avatar
    Join Date
    Nov 2006
    Location
    Newcastle, WA
    Posts
    4,997
    Nice work and ambitious project!!!

    Are you planning on ceramic coating of the manifold and piping?
    Probably will help keep some of the heat down.
    SOLD - 03 RS6 Avus (905355)
    Current - 03 Toyota Tacoma 4x4 double cab - the YETI, lifted, winched, snorkeled, lockered, skidded, geared

  14. #14
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Quote Originally Posted by ben916 View Post
    Nice work and ambitious project!!!

    Are you planning on ceramic coating of the manifold and piping?
    Probably will help keep some of the heat down.

    Nice thinking ;-) , this was all about 1 1/2 years ago at this point, I'm just catch up posting pics so people can see what was done
    OZ RS6, 0A3 manual, Tilton Carbon/Carbon Triple Plate, twin GTX3071s, twin Tial mv-s gates, Custom ICs, BMC OTA filters, A8 MAFs, 980cc injectors, etc

  15. #15
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    FX850 clutch

    Click image for larger version. 

Name:	ClutchFX850001.jpg 
Views:	3006 
Size:	65.1 KB 
ID:	15000


    Click image for larger version. 

Name:	ClutchFX850002.jpg 
Views:	3119 
Size:	65.2 KB 
ID:	15001

    Individual pieces laid out
    Click image for larger version. 

Name:	ClutchFX850003.jpg 
Views:	2981 
Size:	75.0 KB 
ID:	15002

    Test fitting on the engine
    Click image for larger version. 

Name:	ClutchWithSpacerToneRing.jpg 
Views:	3089 
Size:	92.5 KB 
ID:	15003

    Attaching tone ring in the right orientation, also had to machine a channel behind the tone ring as there was not one when it arrived, fine for Alu but not good for Steel
    Click image for larger version. 

Name:	ToneRingFitted.jpg 
Views:	3054 
Size:	72.9 KB 
ID:	15004
    OZ RS6, 0A3 manual, Tilton Carbon/Carbon Triple Plate, twin GTX3071s, twin Tial mv-s gates, Custom ICs, BMC OTA filters, A8 MAFs, 980cc injectors, etc

  16. #16
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Clutch hit the gearbox when first fitted...... :-(
    Click image for larger version. 

Name:	Bell Housing Rubbing.jpg 
Views:	3223 
Size:	72.0 KB 
ID:	15005

    Click image for larger version. 

Name:	ClutchRubbing002.jpg 
Views:	2932 
Size:	66.1 KB 
ID:	15006

    Spacer for the crank angle sensor
    Click image for larger version. 

Name:	Crank angle sensor spacer.jpg 
Views:	2848 
Size:	52.8 KB 
ID:	15007

    Fabricators comments about the flywheel pre getting it machined to fit.
    Click image for larger version. 

Name:	FabricatorsCommentsFlywheel.jpg 
Views:	2965 
Size:	63.1 KB 
ID:	15008

    Pic of the channel that was cut behind the tone ring to get clean readings
    Click image for larger version. 

Name:	Flywheel Channel.jpg 
Views:	2844 
Size:	65.6 KB 
ID:	15009
    OZ RS6, 0A3 manual, Tilton Carbon/Carbon Triple Plate, twin GTX3071s, twin Tial mv-s gates, Custom ICs, BMC OTA filters, A8 MAFs, 980cc injectors, etc

  17. #17
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Modifying the Intake MAF pipe, this was modified to accept R32/B5 S4 MAFs but also the tiny diameter to the turbos was enlarged to nearly twice the diameter. And then Coated

    Click image for larger version. 

Name:	MAFPipeMod.jpg 
Views:	2885 
Size:	63.4 KB 
ID:	15011

    Downpipes finished and ceramic coated
    Click image for larger version. 

Name:	DumpsCeramicCoated.jpg 
Views:	2951 
Size:	67.4 KB 
ID:	15010

    Other components coated and nearly ready to put back in, after a little cleaning up of the ports
    Click image for larger version. 

Name:	ManifoldsHousingsCoated.jpg 
Views:	2873 
Size:	67.5 KB 
ID:	15012

    Tailshaft length modified, rebalanced and ready to go
    Click image for larger version. 

Name:	ResizedTailShaft.jpg 
Views:	2852 
Size:	74.0 KB 
ID:	15013

    B7 RS4 starter motor vs stock RS6 on the left
    Click image for larger version. 

Name:	StarterMotors.jpg 
Views:	3014 
Size:	68.5 KB 
ID:	15014

    Starting to put titanium heat wrap on exhaust manifolds
    Click image for larger version. 

Name:	WrappingManifolds.jpg 
Views:	2889 
Size:	117.4 KB 
ID:	15015
    OZ RS6, 0A3 manual, Tilton Carbon/Carbon Triple Plate, twin GTX3071s, twin Tial mv-s gates, Custom ICs, BMC OTA filters, A8 MAFs, 980cc injectors, etc

  18. #18
    Registered User
    Join Date
    May 2010
    Location
    Sydney
    Posts
    97
    Manifold wrapped and test fitted
    Click image for larger version. 

Name:	Dry Wrap.jpg 
Views:	2942 
Size:	98.8 KB 
ID:	15021

    Some custom fittings machined up to get all the dash fittings to connect to engine, clutch, etc
    Click image for larger version. 

Name:	Custom Milled bits 002.jpg 
Views:	2890 
Size:	58.5 KB 
ID:	15016
    Click image for larger version. 

Name:	Custom Milled bits 004.jpg 
Views:	3006 
Size:	65.5 KB 
ID:	15018
    Click image for larger version. 

Name:	Custom Milled bits 005.jpg 
Views:	2833 
Size:	96.7 KB 
ID:	15019

    Click image for larger version. 

Name:	Custom Milled bits.jpg 
Views:	3086 
Size:	36.5 KB 
ID:	15020


    New machined connection to the clutch slave, still uses the stock plastic fitting but allows dash teflon lines to be used, also created a dash fitting on the bleed for a remote bleed in the top of the engine bay, no need to get under the car to bleed the clutch!
    Click image for larger version. 

Name:	Custom Milled bits 003.jpg 
Views:	2960 
Size:	61.0 KB 
ID:	15017
    OZ RS6, 0A3 manual, Tilton Carbon/Carbon Triple Plate, twin GTX3071s, twin Tial mv-s gates, Custom ICs, BMC OTA filters, A8 MAFs, 980cc injectors, etc

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •