RS6 6 speed Manual Swap Update CAR RUNNING!!!! With Sneak peak ER RS6 intercoolers

[Matt@ravenms]

Just finished the Car and made some videos, sorry but they're Crappy Iphone videos. Should make some better ones soon. But for now this is All i got....

BTW I used a Stock clutch, and it slips pretty Badly, way too much power. SO, I'm getting a stage 4 on Tuesday and going to install it over the week. There were a lot of things that needed to be modified to make the complete swap work correctly. Again as before in other post, i did not use ANY adapter plate nor aftermarket parts Other then flywheel/pressure plate/dics which was a giving. I have stock oem Starter and everything else.... Car starts and drives fine.... Even with Clutch slipping it's still pretty damn quick. So far logged 100 miles on car, 3 doughnuts, and much more to come!!!!

So far mods on car are Manual 01E 6 speed w Alum flywheel, Tuned ECU(chipped), piggys, and removed radiators behind Intercoolers AND for Test fitting and prototyping ER intercoolers Sneak peak Hope you like!









Thanks for Following the swap, PM me if your interested in Getting swap Done
Here's youtube links

http://www.youtube.com/watch?v=dYCGbVfV258

http://www.youtube.com/watch?v=Gq1jpJ1mxlo


Excuse the interior of the Car. wasnt concern on finishing trim pieces or Airbag LOL BTW that's a R8 steering wheel

[MaxRS6]

Congrats on the progress, and good luck with the continued success!

[ben916]

Awesome!!!!

FINALLY, no more slipping slush box!

BTW, where are you located? nevermind, found ya!

[JSRS6]

Does the steering wheel work with the radio?

[gooseleg]

Is that a secondary speedo cable on the video?

[snoopra]

Great follow up post! So no adapters, custom starter needed? I hope you'll share the wealth!

[Matt@ravenms]

Awesome!!!!

FINALLY, no more slipping slush box!

BTW, where are you located? nevermind, found ya!

I'm located near Downtown Long Beach off 710 n PCH.

Does the steering wheel work with the radio?

i dont think it does... havent mess w that yet, was focused on getting car driving first....

Is that a secondary speedo cable on the video?

Haha No that's the Shifter interlock for old Shifter from Auto.... the cable that makes you be in park to take key out of ignition. just didnt remove it complete yet...

[Matt@ravenms]

Great follow up post! So no adapters, custom starter needed? I hope you'll share the wealth!

No adapter, and no custom Starter. I'm using all Factory parts(Minus Clutch assembly). There is a lot of fabrication to be done to get everything bolted up, exhaust fitting and working correctly. I don't think this is a Job to do in someones garage.

[snoopra]

Maybe the "PAT CAVE"?

[V8weight]

Maybe the "PAT CAVE"?

Haha, not while I still have warranty left.

[Aronis]

Haha, not while I still have warranty left.

yes, I hear you!

[scottmandu]

No adapter, and no custom Starter. I'm using all Factory parts(Minus Clutch assembly). There is a lot of fabrication to be done to get everything bolted up, exhaust fitting and working correctly. I don't think this is a Job to do in someones garage.

You're failing to omit the modifications you have to do to the engine block (drilling holes etc.) and the omission of at least half the bolts that hold the engine to the transmission.

Good to hear it's running.

[TozoM8]

Cool conversion, congrats! you can just wire tie the ignition lock cable and roll it up behind the dash, that's what I did.

[Matt@ravenms]

Cool conversion, congrats! you can just wire tie the ignition lock cable and roll it up behind the dash, that's what I did.

I'm going to remove it, we finished the car at 7 in the morning...just got real lazy and wanted to drive the car. Just kids in candy store really

[Matt@ravenms]

You're failing to omit the modifications you have to do to the engine block (drilling holes etc.) and the omission of at least half the bolts that hold the engine to the transmission.

Good to hear it's running.

Why the negativity??? I'm not failing to admit any modifications. There was another post that stated everything that I did, I'm not hiding the truth. I'm Missing one bolt... The Same Bolt That is missing on SteveKen Adapter kit... The upper left hand bolt at the 10:30 positon. every other bolt going from Trans thou spacer to engine is there. I have 7 out of 8. As for the lower oil pan area I have 1 out of 2. Even tho the starter area on the engine is slightly grinded down... Car starts with factory Starter, not aftermarket. So ever start feels and Sounds like the original car. I trust OEM over aftermarket any day.

At the end of the day, The car RUNS and Drives great.... Should have been like this from factory. Damn Audi..

[TozoM8]

7 bolts is plenty enough. You also have two dowel pins. The Cadillac northstar has 4 bell housing bolts.

[Matt@ravenms]

7 bolts is plenty enough. You also have two dowel pins. The Cadillac northstar has 4 bell housing bolts.

Yea, I've been working on B5 S4 forever and I've seen guys only running like 6 upper and no lower bolts on oil pan. These are GTRS 2.7T cars making well over 700HP. so if they can handle the Power i think were Good.

Yes, I notice that the adapter kit Steveken has doesn't reuse the Dowel pins, as for me. I'm using both dowel pins. Not to dis the kit Steve.... Very good idea. Just not what I ended up doing

Like I said, Big smile on my face as for the owner too...

Was just curious if anyone interested in Getting there RS6 Converted? Taking appointments now...

[ben916]

Matt,

I don't know about everyone else but I think it is awesome!

questions:
1. How long did it take?
2. How long would it take for the conversion?
3. Are you sourcing the parts/trans?
4. How does this effect aftermarket ECU tunes? I am thinking it gets tossed out with your..
5. The BOTTOM LINE.....$
6. Warranty?