Search:

Type: Posts; User: GreggPDX

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. https://www.move.org/best-car-shipping-companies/...

    https://www.move.org/best-car-shipping-companies/

    :)
  2. The clutch can definitely be "grabby", it's been...

    The clutch can definitely be "grabby", it's been slowly getting better, but with 10K miles, it's probably as good as it's going to get. In most driving it's fine, the only time I still find it...
  3. I forgot to note that EGT's have been...

    I forgot to note that EGT's have been re-soldered. Also, the car will pass Oregon emissions testing without issues. It should also pass any state that uses OBD2 testing or a sniffer test. The...
  4. FS: Oregon - RS6 Misano Red, 6-speed with 92K miles

    Location – Portland, Oregon

    Summary:

    Price - $20K

    Currently at 92K miles
    Misano red with black interior, carbon fiber trim and SE exhaust.
    10K miles on 6-speed swap, with timing belt,...
  5. Replies
    37
    Views
    4,822

    Mine are reversed:...

    Mine are reversed:
    https://www.rs6.com/attachment.php?attachmentid=19357&stc=1

    One thing to keep in mind is that ideally these can easily be removed (particularly the passenger side) because they...
  6. Replies
    37
    Views
    4,822

    Not P1054, but I repaired mine as well, and if I...

    Not P1054, but I repaired mine as well, and if I recall correctly, I just carefully pried the case open, using a sharp blade and patience. I did the re-solder per this thread:...
  7. Replies
    35
    Views
    5,821

    The engine alone is worth 4500, but obviously you...

    The engine alone is worth 4500, but obviously you need to deal with parting it out of you want to go that path. Is the front bumper intact? In any case, you probably have $10K in just the big...
  8. Replies
    114
    Views
    17,762

    Looks good! Regarding the SAI solenoid, I also...

    Looks good! Regarding the SAI solenoid, I also had nubcake tune it out, and I did the "loopback" and capped the tee where the "S" hose is attached. Worked fine, no codes.
  9. Replies
    35
    Views
    5,821

    My wife's standard response is "JESUS CHRIST...

    My wife's standard response is "JESUS CHRIST GREGG, KNOCK IT OFF!", usually followed by comments about how I still act like a teenager. I take these as a compliment. Another recent response from a...
  10. Replies
    8
    Views
    1,756

    Those look amazing! I love the two-tone, very...

    Those look amazing! I love the two-tone, very classy!!!
  11. Replies
    114
    Views
    17,762

    I don't believe lifter failure is a regular thing...

    I don't believe lifter failure is a regular thing with these cars, although what you are describing sounds pretty mild. I have occasionally had a mild "tic" for a few minutes on start-up after...
  12. Replies
    40
    Views
    8,763

    I'm still rocking the DRC on mine with the...

    I'm still rocking the DRC on mine with the Hotchkis ARB's, and I like it a lot, but I know my days are numbered with that setup. I had the PSS9's on a B7 A4, and they were pretty stiff. Handled...
  13. Replies
    114
    Views
    17,762

    On the wheel bearing thing, I suspect is makes a...

    On the wheel bearing thing, I suspect is makes a pretty big difference whether the engine is installed, or not. There is not much weight on the front when the engine/trans are out. Also, I always...
  14. Replies
    114
    Views
    17,762

    I'm confused, how does rolling the car without...

    I'm confused, how does rolling the car without the axles installed destroy the bearings? I'm quite sure I rolled mine around quite a bit during the my 6-speed swap, and I haven't had any issues with...
  15. Replies
    10
    Views
    1,875

    This one looks nice, and much more reasonable...

    This one looks nice, and much more reasonable price - https://seattle.craigslist.org/sno/ctd/d/lynnwood-2003-audi-rs6-awd/7177556002.html
  16. Replies
    23
    Views
    4,183

    Slave 1 is Boba Fett's ship, so it was fun to...

    Slave 1 is Boba Fett's ship, so it was fun to find a Star Wars nerd parking buddy!

    Yes, those are LM's, and they are exactly the same as your size:...
  17. Replies
    23
    Views
    4,183

    Not really recent, but it's newest one I could...

    Not really recent, but it's newest one I could find on my phone. Bonus points if you can figure out why these two cars are related!
    https://www.rs6.com/attachment.php?attachmentid=19277&stc=1
  18. Replies
    8
    Views
    1,392

    I used Loctite 518 because I read it was better...

    I used Loctite 518 because I read it was better for aluminum. I used the same CHRA's on mine and installed them myself. It was pretty straightforward, but I struggled quite a while disassembling...
  19. Replies
    3
    Views
    987

    I don't think there are many people that have...

    I don't think there are many people that have done a manifold upgrade without a lot of other changes at the same time, so it's probably going to be hard to get an objective answer. I suspect a lot...
  20. My understanding is the interval might be related...

    My understanding is the interval might be related to the bearings. Those belts should not wear significantly faster than other cars, but the guide rollers are stupidly small. You could probably run...
  21. The car looks really nice, and it shows a very...

    The car looks really nice, and it shows a very high level of care and maintenance, which is critical for these cars. I think you are going to dinged on the timing belt. I know it's still within the...
  22. Replies
    19
    Views
    3,587

    If anyone wants a spare transmission to keep on...

    If anyone wants a spare transmission to keep on the shelf, I've got a good one that I pulled at 82K for my manual swap. It was actually working fine, but I am a 3-hour drive from AMD, so if someone...
  23. Mine were done around 82K miles while the motor...

    Mine were done around 82K miles while the motor was out for the trans swap, and they looked almost exactly like yours. A bit of wear, but not bad.
  24. When I did it, I'm pretty sure I just used blue...

    When I did it, I'm pretty sure I just used blue RTV. I don't remember exactly why I chose that sealant, it's possible it came with the Blauparts kit that I used. I guess I don't understand how the...
  25. Replies
    16
    Views
    2,376

    Pics or it didn't happen! :)

    Pics or it didn't happen! :)
Results 1 to 25 of 282
Page 1 of 12 1 2 3 4