Search:

Type: Posts; User: bethridg

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Behind the lower center grille; originally...

    Behind the lower center grille; originally attached to the plastic duct that feeds the oil/trans cooler if you still have it. Drivers side as nubcake mentioned. Will look something like this.
    ...
  2. Replies
    48
    Views
    1,664

    I'm not saying your motor hasn't been apart...

    I'm not saying your motor hasn't been apart recently but I had the same sharpie L & R on the two BCYs I have in my possession. Change the tensioner pads! You truly don't know the history, especially...
  3. I do not have any experience with the Audi 100...

    I do not have any experience with the Audi 100 pump. From the outside, they appear to be the same as the RS6/S6/A6-4.2 units. However, comparing across multiple aftermarket manufacturers (rockauto)...
  4. Replies
    48
    Views
    1,664

    I just pulled these fasteners off my spare block....

    I just pulled these fasteners off my spare block. 7mm hex socket. If you have something different it's something I haven't come across one these motors and I'm really curious.

    19013
    19014
    ...
  5. Replies
    48
    Views
    1,664

    OG 6-speed swappers coming out of the wood work...

    OG 6-speed swappers coming out of the wood work to share the knowledge :)


    GreggPDX covered most everything.

    Manifold: I'm pretty sure the manifold nuts should be hex key centered. I don't...
  6. Replies
    16
    Views
    854

    hahnmgh63, Are you still running stock turbos...

    hahnmgh63,

    Are you still running stock turbos or did I miss you upgrading to SRM hybrids?
  7. I have a brand new brake booster in the box. Make...

    I have a brand new brake booster in the box. Make me an offer if you're interested.
  8. Replies
    3
    Views
    259

    For manifold flanges, I've had these on my watch...

    For manifold flanges, I've had these on my watch list for a few years now.
    ...
  9. Replies
    11
    Views
    881

    The radiator is most definitely specific to the...

    The radiator is most definitely specific to the RS6 and not shared with any other trim level. Your options are limited for replacement. They may still be available from Audi but I've seen plenty of...
  10. Replies
    16
    Views
    1,630

    Something else is wrong if you're really slipping...

    Something else is wrong if you're really slipping that clutch especially with your timing being fucked.
  11. Replies
    204
    Views
    160,818

    It did cross my mind...but I don't have anything...

    It did cross my mind...but I don't have anything to weld aluminum yet. Still rocking the rubber caps at that location. Should look into those silicone caps hahnmgh63 mentioned above. I go into panic...
  12. If you haven't already, the o-rings at the top of...

    If you haven't already, the o-rings at the top of the injector (inserted into the fuel rail) can be replaced also. They are the same as the lowers.

    While you're in there... :D
  13. Replies
    72
    Views
    8,732

    I guess I was referring to the gauge cluster...

    I guess I was referring to the gauge cluster showing "Press clutch pedal to start engine" when the TCU is disconnected. I'd prefer no ABS/ESP with less erratic drive for a short period of time until...
  14. Replies
    72
    Views
    8,732

    Avus/Ebony aka black/wood trim. I've ran across...

    Avus/Ebony aka black/wood trim. I've ran across ~230 VINs since I started keeping record a couple years ago. Amazed it took this long for yours to surface.

    Pin #39 to the clutch safety switch will...
  15. Replies
    204
    Views
    160,818

    Front pipe is galvanized(?) steel; it's magnetic....

    Front pipe is galvanized(?) steel; it's magnetic. I cut off the nipple and welded it shut after replacing the rubber caps multiple times.


    https://i.imgur.com/q9F2Erb.gif
  16. Replies
    72
    Views
    8,732

    Did you wire up pin #39? 905594??? Heh, check...

    Did you wire up pin #39?

    905594??? Heh, check my sig.

    Also, disconnect your TCU :)
  17. Replies
    4
    Views
    508

    You should be able to source the hose from any...

    You should be able to source the hose from any major auto parts store; in my case Autozone. It's just PCV hose but I don't recall the size. Actually, I believe the closest match for the smaller...
  18. Replies
    4
    Views
    508

    I've done it both in and out of the car. It's...

    I've done it both in and out of the car. It's completely do-able in situ but you're going to have a ton of fun fighting with the tight quarters.

    The MAF housing is bolted to the back of the intake...
  19. Searching this site, the previous owner appears...

    Searching this site, the previous owner appears to be JSRS6. Protip: search for the last 6 digits not the full VIN. :)
    ...
  20. This was my MTM chipped TCU. I have no idea how...

    This was my MTM chipped TCU. I have no idea how to identify now that they are flashing the stock chip.

    https://i.imgur.com/HoogYsrh.jpg
  21. Replies
    7
    Views
    1,818

    Don't mean to jump in on a for sale thread but...

    Don't mean to jump in on a for sale thread but the following is the adapter harness and antenna extension cable I used. I tapped into the roof mount shark fin for GPS but you can also source a...
  22. Replies
    9
    Views
    1,271

    I see 905743 but could be wrong. Neither of which...

    I see 905743 but could be wrong. Neither of which I have any info on. Which just means there are still more Beasts out there quietly breaking hearts stop light to stop light.
  23. Thread: Raxles?

    by bethridg
    Replies
    17
    Views
    2,953

    Unfortunately, I do not have any information on...

    Unfortunately, I do not have any information on that front. I can only weigh in on my setup. Standard 6MT stage 1 (Daz) tune with no concerns. You may reach out to Corbett to see what he's running at...
  24. Thread: Raxles?

    by bethridg
    Replies
    17
    Views
    2,953

    I paid $250 + $100 core charge per side since...

    I paid $250 + $100 core charge per side since mine were not usable.
  25. Thread: Raxles?

    by bethridg
    Replies
    17
    Views
    2,953

    Sorry, I was referring to the behavior of the...

    Sorry, I was referring to the behavior of the Torsen diff when my axle broke; got the terminology all wrong. Getting stranded on an incline halfway into a parking lot during rush traffic was not fun.
Results 1 to 25 of 355
Page 1 of 15 1 2 3 4