Search:

I have been experiencing this as well, although not as frequently. Both those lights come on while either driving or stopped while the car is running. It has probably been about 3 - 4 years since I...

I replaced my DRC - probably about 5 years or so ago and went with the Koni FSD inserts, and replaced all the rubber components and bushings, etc while in there. I did the work myself - it was a...

So I need to install a hitch and wiring on the wife's rig. The factory OEM kit 8R0 092 115 is no longer available. I can get a hitch made by Draw Tite which compares to the factory hitch. I would...

I think you will find the aftermarket ones will not have the third port for the after-run coolant pump. I looked at many pictures and none had it. You can search on my post. I went with a OEM one...

For what it's worth, I replaced mine about 3 yrs ago now with one from ORrielly's - it was the original German pump (a rebuild - life time Warramty) I believe it was about $100. No issues. Make...

Got the new radiator in yesterday, kind of a PITA. I wound up buying it form audiusaparts.com - went with the OEM (not really a aftermarket option, unless you go custom). There is a place in...

18968

Picture of Project

Pulled the radiator out this weekend kind of a project. Tried really hard not to have to remove the A/C condensor coil - ultimately had to. Lost about 1 Qt of Trans fluid from the radiator and...

So I tried a repair with a 2 part high temp epoxy on the crack (plastic side). I did not hold. So now it looks like a replacement.

For the first time I saw the low coolant symbol light up on the display. Checked it and yes it was low (slightly), topped it off about a week later same thing. So I start to look around, found...

I read that it is the cat on the driver's side. The CEL has been coming on a couple times in the last month. Should I pursue replacing the CAT? I wonder if my previous issues with the misfires...

So all done as of last weekend (GreggPDX was there to help out and much needed second set of eyes). Car is really running MUCH stronger now - had many leaks, old diverters, leaky/separated suction...

What options on upgrades are there and cost? I do have a Stage 1 tune, but was not really wanting to replace them at this time.

Thanks

Update:

So I did get off - Yes a major PITA !

A big Thanks to Bethridg and Bigglezworth for their tips!!

So now the reinstall.

So on trying to replace the orings on the fuel injectors,...

Sent you a PM earlier today

Thanks

Thanks for the info. Where did you source the larger hoses (and any pre-bent elbows/sections) ?

So will attempt to pull the intake manifold to replace the leaking gaskets as well as the diverter valves, check valves and the suction pump and hoses. Any tips or comments on this procedure. It...

So as I work to pull the intake manifold on the beast, I'm going to replace (hoses, diverter valves, one way check valves, suction pump to name most). I'm going to order a real of silicone 3.5 mm...

OK - Yes there is/are vacuum leaks. I unplugged both pre02 plugs from the harness - rough idle still there, misfires. Also meant to comment that after initial starting and backing out of garage,...

Update:
So I found the drivers side pre cat 02 sensor wiring appears to have shorted (his was on harness mating connector that was replaced some years ago by dealer). Also found some of the small...

So as I am looking at the measuring blocks (car running), I smell an odor and notice smoke coming from the drivers side fire wall/engine - could not exactly isolate it. Shut down car and now have...

I did replace the plugs. So drove the car and warmed it up came back and did a scan. Fuel Trim Bank 1 and 2 showed up - system too lean. Did some measuring blocks; 001,002,003 091,092,093 (the...

Yes I did verify the intake was seated well, I did wrap one layer of electrical tape around the portion that actually seats in the intake manifold - it seemed to snug up the fit. I am going to do...

Do you know off the top the measuring blocks for the fuel trim (lambda) on the RS6 ?

Thanks

How big of a project is it to replace them ( I do have a new set)?