Search:

I have a pair of factory Recaro seat bases that allow easy installation of aftermarket Recaro's into the C5 platform. These came originally on the European C5 A6 and same era VW Passat. They have...

These are SOLD!

Bump - make me an offer, I need these gone!

H&R Sport Spring set p/n 29298-1 in excellent condition. These were only used for a short time on the car by the previous owner.

From the manufacturer:

'The most popular spring in H&R's...

Set of OEM RS6 wheels in excellent condition. These were taken off early in the life of the car, so very little wear and tear.

Located in Portland, Oregon, prefer local sale, but I can ship at...

Car is sold! New owner picked it up yesterday and is driving it back to Texas. He has been browsing the boards here a lot, so I expect we will see him and the car more in the future. It's...

Never dyno'd it, but I agree it would by nice to know.

Wow, maybe I need to post mine there!

Bump, still available!

https://www.move.org/best-car-shipping-companies/

:)

The clutch can definitely be "grabby", it's been slowly getting better, but with 10K miles, it's probably as good as it's going to get. In most driving it's fine, the only time I still find it...

I forgot to note that EGT's have been re-soldered. Also, the car will pass Oregon emissions testing without issues. It should also pass any state that uses OBD2 testing or a sniffer test. The...

Location – Portland, Oregon

Summary:

Price - $20K

Currently at 92K miles
Misano red with black interior, carbon fiber trim and SE exhaust.
10K miles on 6-speed swap, with timing belt,...

Mine are reversed:
https://www.rs6.com/attachment.php?attachmentid=19357&stc=1

One thing to keep in mind is that ideally these can easily be removed (particularly the passenger side) because they...

Not P1054, but I repaired mine as well, and if I recall correctly, I just carefully pried the case open, using a sharp blade and patience. I did the re-solder per this thread:...

The engine alone is worth 4500, but obviously you need to deal with parting it out of you want to go that path. Is the front bumper intact? In any case, you probably have $10K in just the big...

Looks good! Regarding the SAI solenoid, I also had nubcake tune it out, and I did the "loopback" and capped the tee where the "S" hose is attached. Worked fine, no codes.

My wife's standard response is "JESUS CHRIST GREGG, KNOCK IT OFF!", usually followed by comments about how I still act like a teenager. I take these as a compliment. Another recent response from a...

Those look amazing! I love the two-tone, very classy!!!

I don't believe lifter failure is a regular thing with these cars, although what you are describing sounds pretty mild. I have occasionally had a mild "tic" for a few minutes on start-up after...

I'm still rocking the DRC on mine with the Hotchkis ARB's, and I like it a lot, but I know my days are numbered with that setup. I had the PSS9's on a B7 A4, and they were pretty stiff. Handled...

On the wheel bearing thing, I suspect is makes a pretty big difference whether the engine is installed, or not. There is not much weight on the front when the engine/trans are out. Also, I always...

I'm confused, how does rolling the car without the axles installed destroy the bearings? I'm quite sure I rolled mine around quite a bit during the my 6-speed swap, and I haven't had any issues with...

This one looks nice, and much more reasonable price - https://seattle.craigslist.org/sno/ctd/d/lynnwood-2003-audi-rs6-awd/7177556002.html

Slave 1 is Boba Fett's ship, so it was fun to find a Star Wars nerd parking buddy!

Yes, those are LM's, and they are exactly the same as your size:...