Search:

Type: Posts; User: Elevens

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    161
    Views
    49,658

    Totally Agree. Dyno numbers never really meant...

    Totally Agree. Dyno numbers never really meant anything to me, only good for relative before and after comparisons. 1/4 mile times are what counts and Marks numbers have been extremely Impressive,...
  2. Replies
    5
    Views
    1,338

    Very Happy with it so far. Rich utilizes good...

    Very Happy with it so far. Rich utilizes good fueling and timing for his power rather than excessive boost. Upstairs this thing pulls like there's no end in sight. It actually pulls harder as I get...
  3. Replies
    5
    Views
    1,338

    How do you like the Milltek race pipes and the...

    How do you like the Milltek race pipes and the non resonated system? Beautifull noise eh. Not to overpowering but brutal when when you drop the hammer......
  4. Replies
    38
    Views
    6,012

    Glad it worked out for you. You've probably...

    Glad it worked out for you. You've probably tossed out the old pads by now, but if you cut the plugs off them and connect the 2 wires together (shorted them) and then plugged them back into the brake...
  5. Replies
    6
    Views
    1,889

    Why do you want to know? Are you thinking about...

    Why do you want to know? Are you thinking about picking up a set?
  6. Replies
    15
    Views
    2,822

    Tozo is Extremely Knowledgeable on our particular...

    Tozo is Extremely Knowledgeable on our particular Transmission, go with him. 517 is also very good which is who I went with. But if there is a second time around (which I hope not) I will definitely...
  7. Replies
    14
    Views
    6,078

    No No! Running Milltek Race Pipes (Catless...

    No No! Running Milltek Race Pipes (Catless Downpipes) with full Milltek Non res Setup and its just perfect. This is my Everyday Driver (60 miles everyday) and I just love to drive this thing. The...
  8. Replies
    38
    Views
    6,012

    Are you sure? Stocks are 14.5" It would be...

    Are you sure? Stocks are 14.5" It would be unsafe to put such smaller Rotors up front. Why would any one do that? To save money, Stupid. Any way I would suggest you get the correct Rotors whether...
  9. Replies
    11
    Views
    8,291

    He shifted into Cruising gear at 206mph. Absolute...

    He shifted into Cruising gear at 206mph. Absolute insanity. Man I wish we could get the C6 over hear......................
  10. Welcome to the Club. Beautiful Car, good luck...

    Welcome to the Club. Beautiful Car, good luck with it love the Red. Alternator can be replaced without pulling the front clip. Its a pain but it can be done as many others have done it. Don't know...
  11. Replies
    30
    Views
    5,322

    OMG!! What a Waste. Your C5 should not go down...

    OMG!! What a Waste. Your C5 should not go down like this.......
  12. Won't see much Improvement with just the Milltek...

    Won't see much Improvement with just the Milltek catback alone. Nice deep note and only a little louder than stock (non resonated is also slightly louder than resonated). A less restrictive exhaust...
  13. Replies
    17
    Views
    4,520

    If the Tires are badly worn, I'm almost certain...

    If the Tires are badly worn, I'm almost certain that's the main source of the noise. As I said before the RS was really making a lot of what I thought was Bearing noise, 4 new Tires and complete...
  14. Replies
    17
    Views
    4,520

    Make sure it's not your Tires. I had to have the...

    Make sure it's not your Tires. I had to have the dealer replace the front bearings on my Allroad since I couldn't press them out myself ($800.00 ouch!). However the Growling noise is still there....
  15. Replies
    17
    Views
    3,078

    Welcome to the club Jaquarda. Don't forget to...

    Welcome to the club Jaquarda. Don't forget to post your Location also. Sounds like your missing portable compressor used to inflate the deflated spare. It straps down just in front of the Subwoofer....
  16. Replies
    104
    Views
    53,647

    4 shipped to the door for $1100.00, is very...

    4 shipped to the door for $1100.00, is very enticing indeed. I wonder how good they really are? Weight and quality.................
  17. Agreed! I had a 93V8 Quattro with the 4.2L...

    Agreed! I had a 93V8 Quattro with the 4.2L engine. It had a same problem as Papadoc, It wound up being the Crank Position Sensor. So I would say that's a good call. Hope you get it...
  18. Thread: RS6 shots

    by Elevens
    Replies
    27
    Views
    9,024

    Absolutely Marvelous. Really nice Setup. Colors...

    Absolutely Marvelous. Really nice Setup. Colors match up beautifully and the Stance is perfect. It those wheels come 10" wide I'll probably go for a set. Only Drawback are those Red Tail lights, I...
  19. Sucks! Must Hurt. Hurts me and it's not even...

    Sucks! Must Hurt. Hurts me and it's not even mine.....................
  20. Replies
    17
    Views
    2,408

    Fantastic!! Hope everything works...

    Fantastic!! Hope everything works out......................
  21. Replies
    16
    Views
    2,845

    Very True.................

    Very True.................
  22. Thread: Need help

    by Elevens
    Replies
    6
    Views
    1,342

    He'll definitely get to the bottom it. Looks like...

    He'll definitely get to the bottom it. Looks like an ECU issue for sure. Either a corrupt flash, something got loose in Transit or bad connection resulting in low ECU voltage. Hope you get it...
  23. Replies
    16
    Views
    2,845

    Don't suggest Staggering. For reasons I'm not to...

    Don't suggest Staggering. For reasons I'm not to sure of It's not recommended, it may have to do with different contact patches affecting the ABS system. I staggered on my previous A6 27T with no...
  24. Thread: RS6 Shirts

    by Elevens
    Replies
    12
    Views
    5,327

    Nice but no AUDI logo!!!!!

    Nice but no AUDI logo!!!!!
  25. Replies
    16
    Views
    2,845

    I run a 19"x10" ET35 wheel, which require a 5mm...

    I run a 19"x10" ET35 wheel, which require a 5mm spacer up front to keep the wheel of the bearing carrier. This results in an effective ET30, which I believe is around the stock ET. So an ET of 28...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4