Search:

Type: Posts; User: bilko1

Page 1 of 2 1 2

Search: Search took 0.07 seconds; generated 42 minute(s) ago.

  1. Replies
    7
    Views
    4,182

    I replaced the control module and the code never...

    I replaced the control module and the code never came back, shortly after the cooling fan died so replaced that as well.
  2. Replies
    6
    Views
    3,760

    MRC got 778 without any internal engine...

    MRC got 778 without any internal engine modifications, I'm sure the Cosworth designed bottom end can take more.
  3. Replies
    10
    Views
    13,718

    Good right up thanks, any tips on how to remove...

    Good right up thanks, any tips on how to remove the black stuff they cover the circuits boards with on the later EGT sensors?
  4. Replies
    14
    Views
    5,831

    Can you guys get vredestein ultrac sessanta over...

    Can you guys get vredestein ultrac sessanta over there? a few of us run these in Blighty with good results summer and winter. http://www.tyrereviews.co.uk/Tyre/Vredestein/Ultrac-Sessanta.htm
  5. Replies
    15
    Views
    3,991

    Doug says new box everytime, Grizz says recon ok...

    Doug says new box everytime, Grizz says recon ok and never had one come back but it's my choice. Problem with new Audi box is it is supplied with a converter which i don't want but is necessary for...
  6. Replies
    15
    Views
    3,991

    Another gearbox thread but different.

    I have got my new ACE torque converter and now trying to decide what route to take with the gearbox. I can find no one in the UK that can uprate it like they do in the states so i can either go for a...
  7. Replies
    46
    Views
    19,614

    Mine are heated but not cooled (never seen cooled...

    Mine are heated but not cooled (never seen cooled seats in a c5), they have electric adjustment and lumbar motors can't be much lighter than the US spec ones surely. My Avant has all the options...
  8. Replies
    17
    Views
    5,477

    Sounds like one of the pads got lifted from the...

    Sounds like one of the pads got lifted from the circuit board, you should be able to get it fixed by an electronics expert cheaply.
  9. Replies
    62
    Views
    15,666

    I had my compressions checked recently while...

    I had my compressions checked recently while changing the spark plugs, all cylinders were 165 - 170 psi. The engine has done 76,000 miles.
  10. Replies
    29
    Views
    8,385

    Hey Pat, fancy a trip to the UK to show us how...

    Hey Pat, fancy a trip to the UK to show us how it's done :) everyone over here stills drops the whole lot.
  11. Replies
    11
    Views
    5,504

    The cheap Ebay units are restricted to what they...

    The cheap Ebay units are restricted to what they can do and also ross-tech won't give you any back up. The Ebay one's also die if you upgrade the official software. Buy a real one they are worth it.
  12. Replies
    29
    Views
    8,385

    Nice job, i thought the turbo had to be removed...

    Nice job, i thought the turbo had to be removed to get to the bastard bolt.
  13. Replies
    12
    Views
    9,202

    I guess it's under your drivers carpet as ours is...

    I guess it's under your drivers carpet as ours is definately under our passenger carpet, they suffer from water ingress when the plenum drains get blocked.
  14. Replies
    12
    Views
    9,202

    There is a micro switch in the door mech which is...

    There is a micro switch in the door mech which is operated buy a lever when the door is opened / shut. I had the same problem with my drivers door and had to replace the whole mech as the lever which...
  15. Replies
    54
    Views
    16,758

    What is a "red-neck" reset?

    What is a "red-neck" reset?
  16. Replies
    54
    Views
    16,758

    Was the full code P0741-17125? if so thats the...

    Was the full code P0741-17125? if so thats the dreaded Torque converter imminent death warning is it not.
  17. How do you guys get the engine/trans out? drop it...

    How do you guys get the engine/trans out? drop it down or take front off and pull it out that way?
  18. Replies
    3
    Views
    2,917

    I logged a friends a4 1.9 tdi yesterday as he had...

    I logged a friends a4 1.9 tdi yesterday as he had the usual overboost then lack of power fault after a garage replaced turbo, maf and n75 valve:cry:his map sensor was faulty and showed a reading of...
  19. Replies
    7
    Views
    4,182

    No CEL i just scan regular and this is the...

    No CEL i just scan regular and this is the result. Are there any wiring diagrams available for the RS6 for free.
  20. Replies
    7
    Views
    4,182

    Got my first fault code

    I've had my RS6 since last November and regularly scan it using VCDS and so far it's been fault free http://forum.rs246.com/images/smilies/rs246_kissmyrings.gif Yesterday i did a full scan and got...
  21. Replies
    9
    Views
    7,875

    Sorry to sound dumb but what's a triple square...

    Sorry to sound dumb but what's a triple square and box end in English tools? I'm guessing the triple square is a 12 point socket or spanner (wrench in American i think)
  22. Can any of you guys do a "how to" or run through...

    Can any of you guys do a "how to" or run through the gearbox removal process without removing engine (some pics would be nice) so us UK guys can get our boxes out quicker. We seem to be light years...
  23. Replies
    54
    Views
    22,790

    But Hoppen said it won't work as the tcu's are...

    But Hoppen said it won't work as the tcu's are different in USA.
  24. Replies
    54
    Views
    22,790

    The chip is unused and was bought by the person...

    The chip is unused and was bought by the person while he was in the USA.
  25. Replies
    54
    Views
    22,790

    Not sure what you mean but Europe has a different...

    Not sure what you mean but Europe has a different tcu to USA so this is why Hoppen US chip will not work in EU tcu's
Results 1 to 25 of 34
Page 1 of 2 1 2