Search:

Type: Posts; User: hahnmgh63

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Thread: Spotted

    by hahnmgh63
    Replies
    143
    Views
    47,939

    Not me. Audi USA says there are 2 in the N....

    Not me. Audi USA says there are 2 in the N. America, what's the chance of them both being in Washington State?
  2. Garaging helps but I would say it is the...

    Garaging helps but I would say it is the conditions it is driven in. I've seen multiple NE cars and they all show the effects of Salted roads compared to our West coast cars. If you live in the NE,...
  3. I pull them every time I do a brake job and clean...

    I pull them every time I do a brake job and clean them. Don't have to unhook the wiring, just the single Torx (I think it's Torx) screw and pull it out.
  4. Replies
    4
    Views
    147

    I second that on Nubcake. He'll get you setup...

    I second that on Nubcake. He'll get you setup with a generic file to start you with the 6spd then after you do some logs with ME7logger he'll revise them for you to really get it dialed in. The ME7...
  5. Flexplate to crankshaft bolt is N 90539801 screw,...

    Flexplate to crankshaft bolt is N 90539801 screw, cheese head M10X1X19X11 Unusually cheap too:
    https://www.audiusaparts.com/oem-parts/audi-screw-n90539801
  6. If I remember right that is correct. There are...

    If I remember right that is correct. There are two bolts per flange (3 flanges) on the Torque Converter.
  7. Bolt - Audi (01L-301-127)

    Bolt - Audi (01L-301-127)
  8. What DHall1 said, you definitely need the molding...

    What DHall1 said, you definitely need the molding off for further inspection. I doubt the drain would crack unless someone poked something into it if they had the trim off earlier. Possibly roof weld...
  9. 1904319043

    1904319043
  10. Replies
    48
    Views
    1,890

    Same as the 2.7t as far as the sealant goes....

    Same as the 2.7t as far as the sealant goes. Factory manual shows just a small button of sealant in all of the corners you mentioned where the gasket makes a sharp angle (cam tensioner). My...
  11. The pumps are made by ZF. The pump also looks the...

    The pumps are made by ZF. The pump also looks the same as what's on my 2 Porsche 944 Turbos. I think BMW uses one just like it too. It would be interesting to find if the pump outputs are different.
  12. Replies
    48
    Views
    1,890

    Oh no, I think I have the Tilton starter, don't...

    Oh no, I think I have the Tilton starter, don't know if I'm pre or post Tsunami :) I went with the cast iron slave cylinder and got a Stainless line from USP motorsports and I ran the line behind the...
  13. Replies
    48
    Views
    1,890

    Yes to Nubcake and Alex being the same. He is...

    Yes to Nubcake and Alex being the same. He is great. I think with CA emissions it will have a hard time passing with the SAI system removed. Nubcake can code the SAI system out, he did on mine but...
  14. What he said. On the newer Audi's the bumper...

    What he said. On the newer Audi's the bumper comes off with the re-inforcement bar still bolted on but on the RS6 C5 the bar comes off with the bumper.
  15. 18992 Do you mean part #20? 4D0971828 , #21...

    18992
    Do you mean part #20? 4D0971828 , #21 cover 4A0971839

    P.S. Now I'm thinking you mean the one below this one which isn't shown in that diagram. I'll keep looking.
  16. Replies
    16
    Views
    921

    Still running stock for the most part. They are...

    Still running stock for the most part. They are rebuilt by Scroll with a few newer updates.
  17. Replies
    16
    Views
    921

    Going to drive mine the 35min to work for the...

    Going to drive mine the 35min to work for the first time in about 3yrs now that my manual conversion is finished. Too many other projects (HMMWV, S5, RS5, 944 Turbo, etc...). Thanks to Nubcake I...
  18. Replies
    5
    Views
    414

    Just did some reading. From high readings to low,...

    Just did some reading. From high readings to low, in general it seems it goes Dynojet, Mustang, and Dyno Dynamics so it looks like that was a pretty good pull. I think most agree that a Dynojet is a...
  19. Replies
    5
    Views
    414

    Gotta be somewhere around 550bhp at the crank or...

    Gotta be somewhere around 550bhp at the crank or more? Got the Torque curve? I don't know anything about Dyno Dynamics Dyno's.
  20. Replies
    5
    Views
    404

    I'll also say 2 days with all the right parts...

    I'll also say 2 days with all the right parts sitting there is optimistic. I'll also say that Nubcake is the man to see about doing your manual tune. He'll customize it for you and start easy and...
  21. Glad you found what you needed. I have expanded...

    Glad you found what you needed. I have expanded to 4 pieces in very good condition if anyone needs some.
  22. Replies
    11
    Views
    898

    Steve, do you know if there is a MT radiator for...

    Steve, do you know if there is a MT radiator for those of us with the 6spd now? I would think we'd want something a little larger than a 2.7t or 3.0 radiator.
  23. I may just have to buy one of those front...

    I may just have to buy one of those front brackets myself as a spare since they are so cheap and I can see the possibility of those clip in springs going bad.
  24. https://www.google.com/search?q=4B0919719&oq=4B091...

    https://www.google.com/search?q=4B0919719&oq=4B0919719&aqs=chrome..69i57j69i60&sourceid=chrome&ie=UTF-8
    The suffix on the end if one denotes the color. I guess there is a matte black and a whatever...
  25. 077103947E It's surprisingly cheap at $22.63...

    077103947E It's surprisingly cheap at $22.63 from Sunset Audi.
    https://www.audiusaparts.com/oem-parts/audi-bracket-077103947e
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4