Search:

Type: Posts; User: mbagge01

Page 1 of 7 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    1
    Views
    604

    Proper differential fluid change

    I am doing some maintenance on my Rs6 and had a question regarding proper filling of the front differential as I have found a couple of different opinions. When refilling the front differential, do...
  2. Replies
    5
    Views
    1,049

    I was able to get the apikol transmission mounts...

    I was able to get the apikol transmission mounts in by raising the transmission and lowering the subframe a bit.
  3. Replies
    5
    Views
    1,049

    Do you have to take the entire bracket off the...

    Do you have to take the entire bracket off the transmission to put the mounts on or can you just undo the mounts from the brackets and replace them.
  4. Replies
    5
    Views
    1,049

    Transmission mounts

    I am in the middle of doing suspension and was hoping to find out from someone if it is possible to replace the transmission mounts with engine in. The repair manual says to take the bracket off the...
  5. Replies
    3
    Views
    540

    As an update, I had the removed the entire...

    As an update, I had the removed the entire knuckle and despite throwing everything at it, the front lower control arm will not come out and it severely seized in the knuckle. As a note to anyone who...
  6. Replies
    3
    Views
    540

    I have now tried a torch to it and it will not...

    I have now tried a torch to it and it will not budge. Is it possible that it is so seized in, I will need to replace the whole knuckle
  7. Replies
    3
    Views
    540

    I have run into a problem with getting the front...

    I have run into a problem with getting the front lower control arm out. It is seized at the ball joint section and when I loosened the but, it snapped right off with part of the bolt in it as well. I...
  8. Replies
    3
    Views
    540

    Alignment work.

    I am doing some control arm replacement on my Rs6 and C5 a6 2.7t and as far as the alignment is concerned, is it only the tierod that can be adjusted as I do not see any concentric bolts. I read in...
  9. Replies
    3
    Views
    547

    While this is not a direct one to one comparison,...

    While this is not a direct one to one comparison, my stage 3 2.7t audi in similar conditions, also with larger intercoolers runs around 100f for air intake temps.
  10. Replies
    3
    Views
    547

    Expected air intake

    My rs6 has Wagner intercoolers and I was doing some recent maintenance and noted when watching my air intake temps, they have been around 150-170F during around our 80 degree weather right now at...
  11. Replies
    1
    Views
    501

    I put a fuse in the missing slot and I do not...

    I put a fuse in the missing slot and I do not notice any major differences, but maybe engine starts up a bit faster. Anyone know why there are three fuses for the fuel system.
  12. I talked to my Indy about rear main seal...

    I talked to my Indy about rear main seal replacement and they say it requires the engine out to do. Is that needed?
  13. Replies
    1
    Views
    501

    Fuel pump question

    I was some maintenance on the rs6 and decided to change the fuel filter. When I went to pull fuse 28 for the fuel pump to empty fuel from the line, but it was missing. My car overall seems to have...
  14. Cleaning the area up and looking more closely, I...

    Cleaning the area up and looking more closely, I think it is coming from my rear main seal. Any need to deal with it if small leak.
  15. I have not tried to check the level yet. As you...

    I have not tried to check the level yet. As you know, there is no drain plug and just a fill plug for the front diff that looks not easy to get to without taking the wheel off and possibly some other...
  16. Advice tracking down a differential leak.

    I have been finding a fair amount of fluid buildup on the bottom of the cover for the front axle differential on the passenger side on my rs6. I know that leaks are common at the seal for the flanged...
  17. Replies
    2
    Views
    473

    Strange wheel noise

    On my RS6, I have been noticing a weird howling type sound in the left front of the vehicle, which sounds like it is around the left front wheel. It has been happening randomly over the past few...
  18. Replies
    2
    Views
    846

    I am sending it to module masters as I have also...

    I am sending it to module masters as I have also had a good experience with them in the past. I will then go the route of removal the wheel well liner to get to it. I actually had a leaking...
  19. Replies
    2
    Views
    846

    ABS electronic module removal

    Does anyone have any tips on getting the electronic part of the ABS module removed as I need to send mine off to get repaired. Do I need to remove the drivers side fender liner and the washer fluid...
  20. Replies
    14
    Views
    6,513

    I did some research and confirmed that I do need...

    I did some research and confirmed that I do need the updated cover to go with the updated flange and seal. I have looked everywhere and cannot find anyone who sells this part. Anyone on this forum...
  21. Replies
    14
    Views
    6,513

    I have developed a pretty bad leak at the prop...

    I have developed a pretty bad leak at the prop shaft and considering instead of just replacing the old design seal, upgrading and flange/shaft and newer seal. I noticed that it was also mentioned to...
  22. hahnmgh63 is correct it is metal, not plastic....

    hahnmgh63 is correct it is metal, not plastic. The part number is 077121071bt. It pipe itself does not bend but it will flex away from the valve cover when he front bolt is removed and it is enough...
  23. I am assuming that you are talking about the...

    I am assuming that you are talking about the black plastic coolant pipe that runs under the valve cover on the right side. If so, yes you just need to remove the front bolt and you only need to flex...
  24. You do not need to remove the rear coolant line...

    You do not need to remove the rear coolant line bolt to get the valve cover off. You only need to remove the front one and the pipe can flex enough to get it out. What I also had to do was loosen the...
  25. I noticed that the valve cover set comes with a...

    I noticed that the valve cover set comes with a half blue moon gasket but it does not look like it is used anywhere unless I am wrong. I know there is one placed under the cam tensioner bracket but...
Results 1 to 25 of 167
Page 1 of 7 1 2 3 4