Register
Help
Remember Me?
What's New?
Forum
New Posts
FAQ
Calendar
Community
Albums
Member List
Forum Actions
Mark Forums Read
Quick Links
Today's Posts
View Site Leaders
Advanced Search
Member List
GreggPDX
Welcome to RS6.com! If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
GreggPDX
Registered User
Find latest posts
Find latest started threads
Mini Statistics
Join Date
May 28th, 2015
Last Activity
Yesterday
19:14
Tab Content
GreggPDX's Activity
About Me
Tab Content
All
GreggPDX
Friends
Photos
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
December 4th, 2019,
17:41
GreggPDX
replied to a thread
evaluating a rear main seal job... what else?
in
RS6 / S6 / RS7 / S7 / S8
I was thinking of the flexplate-to-crank bolts, not torque converter-to-flexplate. There are 10 of those, and you can see them here:...
see more
13 replies | 423 view(s)
December 2nd, 2019,
23:05
GreggPDX
replied to a thread
evaluating a rear main seal job... what else?
in
RS6 / S6 / RS7 / S7 / S8
I don't have the numbers for those, sorry. Might try ECS Tuning and see if they list it.
see more
13 replies | 423 view(s)
December 2nd, 2019,
18:50
GreggPDX
replied to a thread
evaluating a rear main seal job... what else?
in
RS6 / S6 / RS7 / S7 / S8
Looks like all the typical trans-out work has already been done on that car. I'd just say that you should have a spare set of flexplate bolts on...
see more
13 replies | 423 view(s)
November 21st, 2019,
01:56
GreggPDX
replied to a thread
OMG, another 6MT conversion thread.
in
RS6 / S6 / RS7 / S7 / S8
Tsunami was 2011, so probably post, but FWIW, I have the Tilton and have had zero problems.
see more
48 replies | 1818 view(s)
November 14th, 2019,
18:32
GreggPDX
replied to a thread
OMG, another 6MT conversion thread.
in
RS6 / S6 / RS7 / S7 / S8
Regarding the SAI, nubcake can definitely code around it to make it pass the readiness test, even with all the hardware removed. We did that on my...
see more
48 replies | 1818 view(s)
November 14th, 2019,
17:56
GreggPDX
replied to a thread
OMG, another 6MT conversion thread.
in
RS6 / S6 / RS7 / S7 / S8
Yeah the old style has both inner and outer hex. @redwoodkiwi, it's possible that the inner hex is stripped out on yours. The new style is much...
see more
48 replies | 1818 view(s)
November 13th, 2019,
22:32
GreggPDX
replied to a thread
OMG, another 6MT conversion thread.
in
RS6 / S6 / RS7 / S7 / S8
The manifold socket is 12mm, and I'm not sure the brand. They are only marked 'Taiwan" and I'm sure it came form some cheap set I acquired over the...
see more
48 replies | 1818 view(s)
November 13th, 2019,
18:43
GreggPDX
replied to a thread
OMG, another 6MT conversion thread.
in
RS6 / S6 / RS7 / S7 / S8
Regarding the rear main, I left mine. It looked good and I was concerned that replacing it could just make things worse.
see more
48 replies | 1818 view(s)
November 13th, 2019,
18:41
GreggPDX
replied to a thread
OMG, another 6MT conversion thread.
in
RS6 / S6 / RS7 / S7 / S8
I see you figured out the flex plate, good job! Regarding the exhaust manifold, you need to find a really thin-wall socket. I found a 1/4' drive,...
see more
48 replies | 1818 view(s)
November 13th, 2019,
18:31
GreggPDX
replied to a thread
OMG, another 6MT conversion thread.
in
RS6 / S6 / RS7 / S7 / S8
One tip I would share is to take a lot of pictures while you are tearing things down. I took tons, and found them useful many times. Regarding the...
see more
48 replies | 1818 view(s)
More Activity
No More Results
No Recent Activity
About GreggPDX
Basic Information
About GreggPDX
Location:
West Linn, OR
Statistics
Total Posts
Total Posts
249
Posts Per Day
0.15
General Information
Last Activity
Yesterday
19:14
Join Date
May 28th, 2015
Find latest posts