Search:

Type: Posts; User: cruzanrs6

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Conclusion of the INtake Manifold gasket replacement projext

    So all done as of last weekend (GreggPDX was there to help out and much needed second set of eyes). Car is really running MUCH stronger now - had many leaks, old diverters, leaky/separated suction...
  2. What options on upgrades are there and cost? I...

    What options on upgrades are there and cost? I do have a Stage 1 tune, but was not really wanting to replace them at this time.

    Thanks
  3. Follow-Up to Removing the intake Manifold

    Update:

    So I did get off - Yes a major PITA !

    A big Thanks to Bethridg and Bigglezworth for their tips!!

    So now the reinstall.

    So on trying to replace the orings on the fuel injectors,...
  4. Replies
    4
    Views
    359

    Sent you a PM earlier today Thanks

    Sent you a PM earlier today

    Thanks
  5. Replies
    4
    Views
    359

    Thanks for the info. Where did you source the...

    Thanks for the info. Where did you source the larger hoses (and any pre-bent elbows/sections) ?
  6. Replies
    4
    Views
    359

    Removing the intake Manifold

    So will attempt to pull the intake manifold to replace the leaking gaskets as well as the diverter valves, check valves and the suction pump and hoses. Any tips or comments on this procedure. It...
  7. Replies
    0
    Views
    97

    Source for vacuum hoses ???

    So as I work to pull the intake manifold on the beast, I'm going to replace (hoses, diverter valves, one way check valves, suction pump to name most). I'm going to order a real of silicone 3.5 mm...
  8. Replies
    20
    Views
    1,203

    OK - Yes there is/are vacuum leaks. I unplugged...

    OK - Yes there is/are vacuum leaks. I unplugged both pre02 plugs from the harness - rough idle still there, misfires. Also meant to comment that after initial starting and backing out of garage,...
  9. Replies
    20
    Views
    1,203

    Update: So I found the drivers side pre cat 02...

    Update:
    So I found the drivers side pre cat 02 sensor wiring appears to have shorted (his was on harness mating connector that was replaced some years ago by dealer). Also found some of the small...
  10. Replies
    20
    Views
    1,203

    So as I am looking at the measuring blocks (car...

    So as I am looking at the measuring blocks (car running), I smell an odor and notice smoke coming from the drivers side fire wall/engine - could not exactly isolate it. Shut down car and now have...
  11. Replies
    20
    Views
    1,203

    I did replace the plugs. So drove the car and...

    I did replace the plugs. So drove the car and warmed it up came back and did a scan. Fuel Trim Bank 1 and 2 showed up - system too lean. Did some measuring blocks; 001,002,003 091,092,093 (the...
  12. Replies
    20
    Views
    1,203

    Yes I did verify the intake was seated well, I...

    Yes I did verify the intake was seated well, I did wrap one layer of electrical tape around the portion that actually seats in the intake manifold - it seemed to snug up the fit. I am going to do...
  13. Replies
    20
    Views
    1,203

    Do you know off the top the measuring blocks for...

    Do you know off the top the measuring blocks for the fuel trim (lambda) on the RS6 ?

    Thanks
  14. Replies
    20
    Views
    1,203

    How big of a project is it to replace them ( I...

    How big of a project is it to replace them ( I do have a new set)?
  15. Replies
    20
    Views
    1,203

    Misfires On all Cylinders - Help

    So the car developed some rough idling a couple weeks ago, does not appear to have an issue when driving (power is good). Only when stopped or in park. Decided to do a plug change as it had been a...
  16. Replies
    1
    Views
    256

    Intercoolers available

    I did the the Wagner kit install. Have my original OEM's available. The tanks are fine, but the cores well you know. I've seen a set sell from time-to-time on the forum.
  17. I used Hillside imports in Oregon for my 2.7T and...

    I used Hillside imports in Oregon for my 2.7T and the RS6. Great Experience.
  18. Follow-up on Headlight Bulb replacement question

    So I did switch the bulb - bulb works. Wound up putting the bulb back in and it's now working. Thinking maybe a bad connection. If the transformer was the culprit, do they start acting up...
  19. Low beam headlight bulb replacement options

    So pass side went out. I priced the Sylvania DS2 at $100 ea. OEM AT dealer is $145. What have others done ?
  20. Replies
    9
    Views
    777

    Thanks. I would like to see the pics. You could...

    Thanks. I would like to see the pics.
    You could also text them to 971-777-0789
  21. Replies
    9
    Views
    777

    Silly Rabbit Intercoolers question

    I learned just today that they are no longer using the OEM tanks. Sean has as source for cast tanks that he is now using (has been for some time). Was having issues issues cleaning, prepping used...
  22. Replies
    5
    Views
    623

    What size are you running on the rears ?

    What size are you running on the rears ?
  23. Replies
    5
    Views
    623

    Tire size question

    I know the OEM wheels are 8.5" x 18" and tires are 255/40 -18. Has anyone run a 265/40 -18 tire on the stock wheels ? I know the (265) tire is about .4" wider than the 255. I have an opportunity...
  24. Replies
    9
    Views
    979

    I believe your issue is that the mirror's...

    I believe your issue is that the mirror's auto-dimming properties are failing and the reflection is becoming obscure/out of focus (mine did this as well). Get a replacement mirror and replace it...
  25. Replies
    0
    Views
    473

    Replacing the turn signal stalk assy

    So it looks like the turn signal assy is the culprit. I tried 3 different hazard switches and the random clicking noise is still present after actuating the turn signal. I did a Audiworld Tech...
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4