There is also more overlap on S8 cams.
But then there are different castings, I now use A8 cylinder head with S8 camshafts, but these cylinder heads lack water outlet at the front edge under the...
Type: Posts; User: RS8
There is also more overlap on S8 cams.
But then there are different castings, I now use A8 cylinder head with S8 camshafts, but these cylinder heads lack water outlet at the front edge under the...
This is NOT CNG injectors.
My 1500cc has part no 0280158333
I don't know the part number on the EV14 1300cc.
The 1000cc I used before is 0280158040, they was bought as flow matched set.
But...
These were just kind warnings and help, if he has not used them yet then maybe it is possible to get them exchanged for bigger, but of course he does not have to do it if he does not want more power....
An example: These 1000cc injectors I used is rated to 3 bar/ 946cc, 4 bar/ 1080cc
With 3bar FPR and E85 they was open 79% on a dyno pull where I got 770hp or 642whp at 1.1 bar boost,
and if I use...
I'm using a injector calculator, and what I found out myself is to always go bigger than you think will work.
These are just kind tips from me so he do not have to buy new ones again in a year or...
But you can buy different EV14 with adapters in top or bottom so it fits and there is several to choose on between 700-957cc
What I can read these 630cc flow this:
3 bar: 612cc / min
4 bar:...
Why did you buy so small injectors when you are going to use E85 ?
630cc will only work for about 500 -550 crank hp on E85 and 3bar fuel pressure.
I have driven on 1000cc EV14 with E85 with RS6...
You're probably right, I myself have no original left,
AN8 fuel lines, Nuke fuelrail, Turbosmart FPR and standalone ecu = MaxxEcu Pro with home built engine wiring harness.
But for me 2pcs of...
Yes it worked, BUT discovered that there were different volts on the 2 outputs? since I use 2 walbro pumps next to each other then one pump now pumped more than the other !
so I then replaced this...
I do not think you can easily know which follower is bad, by just squeezing them together.
Because if the valves are open on 1 cylinder, then there is pressure there, so then the oil is squeezed out...
Yes, but also bigger injectors.
If I use a injector calulator and type in 8 pcs and 1000hp in a turbo engine and 85% duty cycle.
For gasoline = 950cc
For E85 = 1235-1300cc
Bosch
EV14 1000cc =...
With a modern injector like EV14, you can drive with over 2000cc each without problems, (But I could not find any larger EV14 that have the same length etc. as the ones I used, so therefore I bought...
8*1000cc injectors is to small for you with E85, you will need bigger!
I have bought 1500cc now for my car, because I was already up to 84% open time (and it was with less power than you have...
I don't know which brand to look for. But can say that Supertech big valve kit will not fit RS6, because the exhaust valves is to big!
The cheapest is to only change the intake valves to similar,...
Have anyone measure what oil pressure you have in the engine when the oil is hot and at higher rpm?
I can't find any information online about oil pressure in the RS6 engine.
And you can buy "copy" of it from different manufactures here you got some part numbers:
Reinz = 81-35916-00
elring = 728.880
Ajusa = 15083100
Corteco = 20033872B
Goetze = 50-319551-00
You don't have to buy the whole flange as mentioned, you can buy only the OEM sealing,
here it is with part number:
https://www.rs6.com/attachment.php?attachmentid=19182&stc=1
Thanks!
but it is strange that it says " replace bolt and nuts"
because I can't find them in the spare parts catalog?
...
Hi
What is the torque specs for all Crank Bearing Cap Bolts on the BCY engine?
And do anyone have a part number on new bolts and nuts?
The biggest Simota I could find, it has 89mm neck size in and out (I think the RS6 airbox inlett is about 100mm)
Simota SM-BX-007
https://www.rs6.com/attachment.php?attachmentid=19119&stc=1
Yes the curve was higher all the way.
Here is the dyno papier from 2016:
pull 1 with airbox= 609hp
pull 2 No airbox = 634hp
pull 3 with airbox = 613hp
...
With stock RS6 airbox I had 613hp and 864Nm
And with an open airbox I got 634hp and 883Nm
With modified RS6 turbos.
Now I run 2 rounded Simota Carbon fiber airbox and now it is only 2hp...
And how good is these complete cam tensioner units that sells for low price on ebay?
http://www.rs6.com/attachment.php?attachmentid=18961&d=1570005841&thumb=1&stc=1
Do these cheap plastic pads for chain tensioner works good that sells on ebay (from China), or is there anyone who has had problems with them?
18932
Now the same car has 1086HP with 2bar boost
https://www.facebook.com/madnessmotorsport/videos/257962705088381/