Search:

Type: Posts; User: bethridg

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    836

    Something else is wrong if you're really slipping...

    Something else is wrong if you're really slipping that clutch especially with your timing being fucked.
  2. Replies
    204
    Views
    155,695

    It did cross my mind...but I don't have anything...

    It did cross my mind...but I don't have anything to weld aluminum yet. Still rocking the rubber caps at that location. Should look into those silicone caps hahnmgh63 mentioned above. I go into panic...
  3. If you haven't already, the o-rings at the top of...

    If you haven't already, the o-rings at the top of the injector (inserted into the fuel rail) can be replaced also. They are the same as the lowers.

    While you're in there... :D
  4. Replies
    61
    Views
    4,251

    I guess I was referring to the gauge cluster...

    I guess I was referring to the gauge cluster showing "Press clutch pedal to start engine" when the TCU is disconnected. I'd prefer no ABS/ESP with less erratic drive for a short period of time until...
  5. Replies
    61
    Views
    4,251

    Avus/Ebony aka black/wood trim. I've ran across...

    Avus/Ebony aka black/wood trim. I've ran across ~230 VINs since I started keeping record a couple years ago. Amazed it took this long for yours to surface.

    Pin #39 to the clutch safety switch will...
  6. Replies
    204
    Views
    155,695

    Front pipe is galvanized(?) steel; it's magnetic....

    Front pipe is galvanized(?) steel; it's magnetic. I cut off the nipple and welded it shut after replacing the rubber caps multiple times.


    https://i.imgur.com/q9F2Erb.gif
  7. Replies
    61
    Views
    4,251

    Did you wire up pin #39? 905594??? Heh, check...

    Did you wire up pin #39?

    905594??? Heh, check my sig.

    Also, disconnect your TCU :)
  8. Replies
    4
    Views
    388

    You should be able to source the hose from any...

    You should be able to source the hose from any major auto parts store; in my case Autozone. It's just PCV hose but I don't recall the size. Actually, I believe the closest match for the smaller...
  9. Replies
    4
    Views
    388

    I've done it both in and out of the car. It's...

    I've done it both in and out of the car. It's completely do-able in situ but you're going to have a ton of fun fighting with the tight quarters.

    The MAF housing is bolted to the back of the intake...
  10. Searching this site, the previous owner appears...

    Searching this site, the previous owner appears to be JSRS6. Protip: search for the last 6 digits not the full VIN. :)
    ...
  11. This was my MTM chipped TCU. I have no idea how...

    This was my MTM chipped TCU. I have no idea how to identify now that they are flashing the stock chip.

    https://i.imgur.com/HoogYsrh.jpg
  12. Replies
    7
    Views
    1,517

    Don't mean to jump in on a for sale thread but...

    Don't mean to jump in on a for sale thread but the following is the adapter harness and antenna extension cable I used. I tapped into the roof mount shark fin for GPS but you can also source a...
  13. Replies
    9
    Views
    650

    I see 905743 but could be wrong. Neither of which...

    I see 905743 but could be wrong. Neither of which I have any info on. Which just means there are still more Beasts out there quietly breaking hearts stop light to stop light.
  14. Thread: Raxles?

    by bethridg
    Replies
    17
    Views
    2,372

    Unfortunately, I do not have any information on...

    Unfortunately, I do not have any information on that front. I can only weigh in on my setup. Standard 6MT stage 1 (Daz) tune with no concerns. You may reach out to Corbett to see what he's running at...
  15. Thread: Raxles?

    by bethridg
    Replies
    17
    Views
    2,372

    I paid $250 + $100 core charge per side since...

    I paid $250 + $100 core charge per side since mine were not usable.
  16. Thread: Raxles?

    by bethridg
    Replies
    17
    Views
    2,372

    Sorry, I was referring to the behavior of the...

    Sorry, I was referring to the behavior of the Torsen diff when my axle broke; got the terminology all wrong. Getting stranded on an incline halfway into a parking lot during rush traffic was not fun.
  17. Thread: Raxles?

    by bethridg
    Replies
    17
    Views
    2,372

    There appears to be a few different combinations...

    There appears to be a few different combinations of parts that can be used to accomplish the 01e swap. In my case, I have a Euro TDI trans with heavy duty (130mm) inner tripod joints and flanges. The...
  18. Replies
    16
    Views
    1,536

    Yes, my flywheel is from SteveKen's adapter kit....

    Yes, my flywheel is from SteveKen's adapter kit. It was resurfaced with a 7.5mm step. I also pressed in a new pilot bearing. It was removed for the machine work but felt dry and didn't roll smoothly...
  19. Thread: Raxles?

    by bethridg
    Replies
    17
    Views
    2,372

    Bringing this thread back to add my feedback. If...

    Bringing this thread back to add my feedback. If anyone needs to replace axles call Marty @ Raxles! You won't be disappointed. He went above and beyond to help me source replacements after...
  20. Replies
    16
    Views
    1,536

    I'm now running this clutch. With ~1500 miles on...

    I'm now running this clutch. With ~1500 miles on it, I like the feel and engagement WAY more than the AMD Stage 3+ I previously ran. The pedal feel is slightly heavier but the engagement is much more...
  21. I don't have much on this car but it was owned by...

    I don't have much on this car but it was owned by 'sweatnblood' on here a few years ago with 80k out of San Diego.
    ...
  22. Boost hoses have sold. Thank you!

    Boost hoses have sold. Thank you!
  23. Replies
    0
    Views
    231

    FS - RS6 transmission 5HP24

    Removed at 101k miles. Was slipping. Good core. Taking up room in my garage. Make me an offer. Pick up in or near KCMO. Otherwise buyer figures out shipping.

    Also have two TC's; both late VIN....
  24. Still have intercoolers, shrouds and boost hoses...

    Still have intercoolers, shrouds and boost hoses ready to ship. Make me an offer.
  25. Replaced mine with Philips 85122C1 (~$60/ea)...

    Replaced mine with Philips 85122C1 (~$60/ea) after one burned out. 4000k produces a more yellow color. Next time I'll go back to a 5000k or 6000k for the nice clean white.

    Advertiser over on AZ...
Results 1 to 25 of 346
Page 1 of 14 1 2 3 4